I have a sony EVI-D30 camera. I am looking for control software & drivers for it. Ralph - Answered by a verified Camera and Video Technician. Sony EVI-HD1 - surveillance camera overview and full product specs on CNET. Holiday Gift Guide 2020. Best gifts under $30. Sony Evi-d100 Driver For Mac Free; Sony Evi D100 Camera; PTZ Controller supports Sony VISCA protocol. It works well with Sony EVI D30, EVI D70 and EVI D100 cameras respectively. Sony VISCA protocol normally can support a daisy chain of up to sever attached cameras. So, it is also available to control up to several Sony EVI-D series cameras with. Model: EVI-D30 Device Type: Camera GENERAL INFORMATION SIMPLWINDOWS NAME: Sony EVI-D30 Camera Control with Joysticks CATEGORY: Camera VERSION: 2.0 SUMMARY: This module will control the Sony EVI-D30. It uses 2-way RS232 communications, stores up to 25 presets on the Crestron system, and allows camera control using joysticks as well as standard. The EVI-D100/P is a high quality CCD cameras that combine a high-speed, quiet pan/tilt with a wide angle view and 40x zoom (10x optical + 4x digital), all in a compact, easy-to-use package. The EVI-D100/P camera boasts impressive and innovative features such as auto focus, auto white balance and automatic exposure control which provide fast.

Attach the cables required between the video encoder and the camera, then configure the video encoders settings.
Hardware connections:

Connect the video from the camera to the video encoder. On the back of the EVI-D30/31 there is an area labeled “OUT”. Underneath “OUT”, one of the RCA jacks is labeled “VIDEO”. Connect a RCA cable from this to one of the video encoder’s open video in ports. You may need to use an RCA to BNC converter on the side of the cable that is being connected to the 2400/2400+.
Connect the VISCA cable from the COM1 serial port on the 2400/2400+ to the VISCA IN port on the back of the EVI-D30/31.
Next, configure the camera ID on the EVI-D30/31. On the back of the EVI-D30/31, above “OUT” there is an area labeled ‘CAMERA NO.’ witch you can set to 1.

Video Encoder Configuration:
Note this section of configuration is firmware version specific.
AXIS 2400/2401 firmware version 2.xx and AXIS 2400+/2401+ firmware version 3.xx:

Bring the web interface of the AXIS 2400/2400+ up in a browser window.
Click the admin button to enter the administration pages on the video encoder.
Click the icon labeled ‘COM1’ and change the following settings:

- Set ‘Purpose’ to ‘Pan Tilt’
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button

Next click the icon labeled ‘Pan Tilt’ located below the icon for ‘COM1’

- Set ‘Drivers for Pan Tilt’ to ‘Sony EVI-G20/G21/D30/D31’
- Click ‘Save’

Next click the icon for the video input the EVI-D30/31 is attached to

- Set ‘Pan Tilt Serial Port’ to ‘Sony - EVI-G20/G21/D30/D31’
- Click the ‘Driver Specific Settings’ button
- A new browser window will launch to display the parameters.
- Change ‘Camera X has ID’ to ‘no 1’.

- Set the drop down box to the right of ‘no 1’ to ‘D30/D31’
- Click ‘Apply’
- Click ‘Close’

That will complete the PTZ setup.

AXIS 2400/2401 firmware version 1.xx:

Bring the web interface of the 2400 up in a browser window.
Click the admin button to enter the administration pages on the 2400.
Click the icon labeled ‘COM1’ and change the following settings:

- Set ‘Purpose’ to ‘Pan Tilt’
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button My book live dashboard for mac.

Next click the icon labeled ‘Pan Tilt’ located below the icon for ‘COM1’

- Set ‘Drivers for Pan Tilt’ to ‘Sony D30/D31’
- Click ‘Save’
- A new window will appear titled ‘Specific parameter for Sony D30/D31’.
- Change the ‘Camera X is connected to ID’ to ‘ID no 1’ than click 'Apply' and 'Close'.

Next click the icon for the video input the EVI-D30/31 is attached to

- Set ‘Pan Tilt Serial Port’ to ‘COM1 – Sony D30/D31’
- Click Save

That will complete the PTZ setup.

Evi D30 Drivers For Macbook Air

Troubleshooting:
If the EVI-D30/D31 will not PTZ then try the following:

- Check the VISCA cable connection to make sure it is secure
- Recheck all the parameter settings.
- Restart the video encoder and try to PTZ again.

Evi D30 Drivers For Macbook

Evi D30 Drivers For Macbook Pro

Vote, how useful was this article to you?